The Blind Wolf Posted April 29, 2021 Share Posted April 29, 2021 Uhm, I hope my inverter isn't getting shipped until it works as expected. . . Sid, I guess your the middle man. . . Guess I need to PM you with my Honey I shrunk the kids useing linux list. . . Quote Link to comment Share on other sites More sharing options...
Sid Genetry Solar Posted April 29, 2021 Share Posted April 29, 2021 I've already contacted Sean, and we should be able to bump you up to a 2nd shipment inverter with the updated terminal blocks / AC box cover on the end. I've spent the past few hours working on the GS inverter code...trying to get the self-zeroing code working so customers stop getting the annoying "GTM Regulate Fail" error. Then work on testing the revamped parallel code...then once I get that going, maybe later tomorrow Sean can start testing the revamped code, and then we might at long last be good to go...hopefully! 1 Quote Link to comment Share on other sites More sharing options...
Waterman Posted April 30, 2021 Share Posted April 30, 2021 3 hours ago, Sid Genetry Solar said: I've already contacted Sean, and we should be able to bump you up to a 2nd shipment inverter with the updated terminal blocks / AC box cover on the end. I've spent the past few hours working on the GS inverter code...trying to get the self-zeroing code working so customers stop getting the annoying "GTM Regulate Fail" error. Then work on testing the revamped parallel code...then once I get that going, maybe later tomorrow Sean can start testing the revamped code, and then we might at long last be good to go...hopefully! Now I haven't seen that error. Only one other than the CPU not communicating has been the Low Voltage light and message at startup. Which is a bit odd as the Voltage has never been below 26 Volts when powering up. Quote Link to comment Share on other sites More sharing options...
Sid Genetry Solar Posted April 30, 2021 Share Posted April 30, 2021 Seems to be highly dependent on weird power-factor loads + a large bit of parts tolerances inside the inverter connected with absolute constants. Working on it 😉. Quote Link to comment Share on other sites More sharing options...
Tim Posted April 30, 2021 Share Posted April 30, 2021 Finally my #:%\&typing board came up.sid will you please tell Sean not to ship my 2 yet to have more time to work out the kinks? I am no way a tech person I can't even hardly get Sean.please give him my email and number I don't know if he sent me something I had an email about gs but something was wrong and wouldn't let work.i don't even know what parts yuns are talking about with all those abbreviations only ideas.the simplest way to communicate or access wifi for dummies the better.even manually.but to see it on the phone or laptop is cool to monitor.[moderator: redacted private info; please use PMs for private info] I know mechanics and pretty well elec.i was a working in a whole other world besides tech.unles it was about something mechanical different dog.limited at that for mostly big stuff.didnt mean to but in.Tim Quote Link to comment Share on other sites More sharing options...
Tim Posted April 30, 2021 Share Posted April 30, 2021 PS thanks I've watched the videos for a while you guys have came a long way.good work. Quote Link to comment Share on other sites More sharing options...
Sid Genetry Solar Posted April 30, 2021 Share Posted April 30, 2021 Done. Thank you for your patience. Just have so much on my plate, I've got to get things hammered out. Helps now that I'm basically off work, so I can work on this full time now. 1 Quote Link to comment Share on other sites More sharing options...
Sean Genetry Solar Posted April 30, 2021 Share Posted April 30, 2021 Emails have been sent out. I have a long list of orders and yes most people want to wait. Quote Link to comment Share on other sites More sharing options...
The Blind Wolf Posted April 30, 2021 Author Share Posted April 30, 2021 32 minutes ago, Sean Genetry Solar said: Emails have been sent out. I have a long list of orders and yes most people want to wait. Thats Good, maybe Sid will crack the code and I can get my Pups next week as well. Awaiting to see the demo of dasy boiling water like mad. . . Quote Link to comment Share on other sites More sharing options...
Sid Genetry Solar Posted April 30, 2021 Share Posted April 30, 2021 I'll do my best @The Blind Wolf. So many different projects, prioritizing is very difficult, as all of them are important. 1 Quote Link to comment Share on other sites More sharing options...
The Blind Wolf Posted April 30, 2021 Author Share Posted April 30, 2021 1 hour ago, Sid Genetry Solar said: I'll do my best @The Blind Wolf. So many different projects, prioritizing is very difficult, as all of them are important. Poor, Poor Sid, Over worked, Under Paid and a Kick Butt guy that can do it all. I just contacted a company to have a simple, and I mean simple .stl file made of a 17x2.30x5.80: battery case made so I can print it off. . . They wanted $125 bucks a hour their normal rate. . . though I think I'm going to get a deal since well I'm blind and what I requested is so freak simple, if I was able to see again I could do that crap in my sleep and be a rich person lol. Quote Link to comment Share on other sites More sharing options...
MasterCATZ Posted May 2, 2021 Share Posted May 2, 2021 (edited) I can make one for you if you want it will be very basic however no shampfer's or other fancy things I would need measurements in mm Edited May 2, 2021 by MasterCATZ 1 Quote Link to comment Share on other sites More sharing options...
Sid Genetry Solar Posted May 2, 2021 Share Posted May 2, 2021 On 4/30/2021 at 10:48 AM, The Blind Wolf said: Thats Good, maybe Sid will crack the code and I can get my Pups next week as well. Awaiting to see the demo of dasy boiling water like mad. . . FINALLY have the commercial project pretty much done. Might be able to get back to the GS code tonight, madly adding the features customers need/want...getting daisy chain working, plus adding the generator start code (gasp!) Numerous bugfixes and improvements... 1 Quote Link to comment Share on other sites More sharing options...
Tim Posted May 3, 2021 Share Posted May 3, 2021 Thank you both Sid and Sean I know you both have a lot on your plates. Quote Link to comment Share on other sites More sharing options...
The Blind Wolf Posted May 3, 2021 Author Share Posted May 3, 2021 23 hours ago, MasterCATZ said: I can make one for you if you want it will be very basic however no shampfer's or other fancy things I would need measurements in mm Wish I knew that before I spent the money. yeah it was basic. too easy, and sucks it cost so much. Quote Link to comment Share on other sites More sharing options...
The Blind Wolf Posted May 3, 2021 Author Share Posted May 3, 2021 4 hours ago, Sid Genetry Solar said: FINALLY have the commercial project pretty much done. Might be able to get back to the GS code tonight, madly adding the features customers need/want...getting daisy chain working, plus adding the generator start code (gasp!) Numerous bugfixes and improvements... Sweet. Well, tommoro I'll be printing out my battery case that I had design, and its going to be sweet, will have some photos of it when I get them made, each end will have a terminal, yet the cell or cells will be inside sealed and if I could figure out the balancer, once I get them in my hands, I might can incorp them into the design :P. Quote Link to comment Share on other sites More sharing options...
The Blind Wolf Posted May 3, 2021 Author Share Posted May 3, 2021 Just order another 3d printer, taking too long to print one thing. . . Had to break this on down and file the track on the y track cause I didn't noticed that it was damage when I got it and was why it was causeing all the issue with printing big object, among other things, just got it back up going and its 12 hours into a print with no issue. once it get done with this print I'l be printing out two parts for the new printer so I can have it up and going when it arrives. I got to print out two parts per battery cell or cells holder. So just on one bank thats 16 prints I got to do. so will have one do red color and the other do black color since one side is kind of diff with a t seam and the other is a straight edge to go into it. Anyhow, hopeing to get most of it printed off before the inverters show up, cause thats going to suck batteries and I got to bring each bank that I build down to repackage them and so forth to make them safer and easy to deal with. instead of sitting in either a ammno plastic box or a chip tot 😛 The cell holders I got design will allow me to do 18650, 16650 and those big darn presmatic cells I got. Quote Link to comment Share on other sites More sharing options...
MasterCATZ Posted May 3, 2021 Share Posted May 3, 2021 I know the feeling bought a brand new one that failed 3 1/2 roll in , the bearings on the extruder exploded from the looks of it the bearings were rusted ... Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.